GRAT Control Valve、ELECTRIC ACTUATOR、ELECTRIC BUTTERFLY VALVE、ELECTRIC BALL VALVE、ELECTRIC CONTROL VALVE

Pneumatic control valve

HOME > Product Category > Pneumatic control valve >

Category of:Pneumatic control valve

Product Name:Wafer Pneumatic Metal Seal Butterfly Valve

Product introduction:
Classification: Pneumatic Butterfly Valve
Product Name: Wafer Pneumatic Metal Seal Butterfly Valve
Product Description
Wafer Pneumatic Metal Seal Butterfly Valve adopts a "U" type stainless steel seal ring and this precision elastic seal ring and the 3D eccentric polishing disc contact each other to solve the problem that the seal surface is still in the sliding contact friction when the traditional eccentric butterfly valve opened and closed from 0 ° to 10 ° in a twinkle which realizes the seal surface separating when the disc opened in a twinkle and seal recovery when the disc closed and which also achieves the purpose of the best seal performance and prolonged service life. Hence this valve is widely suited to the pipeline of medium temperature ≤ 550 ℃ as the best device to regulate the flow and cut off fluid which is applied in the fields of metallurgy electric power petroleum chemical air gas combustible gas and water supply and drainage and other corrosive medium.
As a device to regulate flow pressure temperature and proportion wafer type pneumatic metal seal butterfly valve is suited to various middle &low-voltage and the powder or liquid medium services.

PRODUCT CHARACTERISTICS

The characteristics of the products
★High temperature resistance good seal performance zero leakage.
Metal sealed pneumatic butterfly valves support the structure of 3D eccentric metal sealed whose seal mode is metal-to-metal also can be changed into the other seal modes such as the metal seal ring to the metal and the stainless steel plate seal ring or the graphite composite plate seal ring to the metal.
In the situation of the high temperature and high pressure this series valves with U type stainless steel seal ring still hold stable seal performance and elasticity whose special seal system guarantees the higher seal performance under temperature range from ultra low temperature to ultra high temperature.
3D eccentric seal system and ergonomic design make the valves have a small opening resistance. The seal surface of the disc presents a convex cone shape. When the valve is opening the every contact around the disc departs from the seal ring at the same time and the solids are hardly accumulated on the seal surface. The process of shutting off the valve is realized by the compression control of elastic seal ring.
Without jam between disc and seal ring seal performance is not affected by temperature changes.
The sealing of the stem axis is realized by graphite-compacted seal ring which assures zero leakage during the whole fire accident process. Hence this kind of valve is called the nature valve of fire safety.
The valve adopts the advanced structure of 3D eccentric metal composite cone canting and can reach up to zero leakage.
The series valves with rubber seal hold the excellent seal performance between the disc and seat when it shut off good two-way seal performance small torque and the series valves ensure zero leakage under the operating pressure.
There is almost no friction between the disc and seat due to its 3D eccentric structure moreover the series have the closer seal performance the further being shut off.
★Small opening torque no frictional rotation long service life
The valve is operated by the working principle that the shaft drive the disc to rotate 90 degrees to realize flexible switch without jam jumpiness and the torque is small.
More than 50000 operation life without fault keep your system operating safely and reliably.
★Small volume light weight quick switch
The valve is comprised of body disc shaft seat and gears which has simple and compact structure light weight convenience in transportation installation and disassembly.
Switch with 90 degree has the advantages of quick switch small torque saving energy.
The valve has excellent modulation performance and whose flow characteristic is approximate to linearity.
★Replacing the body material the different seal ring is suitable for different medium.
With the whole baking finish surfaces the valve can effectively prevent rusting and is suited to different medium by changing better seal rings or seal materials.
The body has high cost-effective especially large diameter butterfly valve (prefer to butterfly valve in the occasions of middle and low pressure) and is configured with a convex pipe flanges. Superior cost-effective performance makes the butterfly valves have a broad scope of application.
★The pneumatic actuator owns excellent performance.
Using the new GT series of pneumatic actuators this valve has a double acting and spring return (spring reset) to realize gear driving safely and reliably. Large diameter valves adopts AW series pneumatic actuator to realize fork transmission which has reasonable structure large output torque a double acting and spring return
1.The gear type double cylinder has large output torque and small volume.
2.The cylinder is made of aluminum alloy with the light weight beautiful appearance.
3.The manual handle can be installed at the top and bottom of valve.
4.The rack type connection can regulate opening angle and rated flow.
5.The actuator can achieve automatic operation when equipped with electrical signal feedback indication and all kinds of accessories.
6.The standard connection ISO05211 provided the convenient installation and replacement for product.
7.Both-sides adjustable screw can make the standard products have ±4° adjustable range at the angle of 0 ° and 90 ° to ensure the synchronous precision with the valve.

Product parameters

The parameters of the products
Body ratings: PN1.0/PN1.6Mpa/PN2.5Mpa
Valve size: DN50-DN1200
Sealed material: Alloy seal
Flow characteristics: approximate EQ%.
Stem seal: NBR/ HNBR/ PTFE/ Graphite
Body material: WCB/SUS304/SUS316L/CF8/CF8LStainless steel
Stem material: WCB/SUS304/SUS316L/CF8/CF8L Stainless steel
Body connections: Wafer/flange
Operating pressure: PN1.6Mpa PN2.5Mpa
Medium Temp. ≤350℃

Product information

The compliance standards of the products
Design standards: GB/T12238-1989
Flange connection size: GB/T9113.1-2000 GB/T9113.2-2000 GB/T9115.1-2000 GB/T9115.2-2000
Structure length: GB/T12221-1989
Pressure test: GB/T13927-1992 JB/T9092-1999
Optional accessories
Please select the accessories according to the different control and requirement.
Accessories to cut off: Single electric control solenoid valve double electric control solenoid valve the signal feedback device of limited switch
Modulation type accessories: The electrical positioner pneumatic positioner electrical converter
Air source treatment accessories: Air-set air source treatment triplet

Manual handle: HVSD manual operation.

The product information
Installation size drawing

The properties specification

The material of the main parts

The pressure and temperature range

The installation size of wafer type

Note: The above connection size of side flange is compliant with the standard GB9113.3-88.
Note: The prolonged size of H1 H2 and H3 is available if need (long stem butterfly valve) please advise us in advance of the special material requirement.

PRODUCT LIST

Download & Catalog

CONTACT US

VIDEO

APPLICATION